# Best Wood Carving Vises: Faceplate Carving Vises, Patternmaker's and Ball Joint

Source: https://carvingbench.com/best/best-wood-carving-vise
Updated: 2026-11-17
Publisher: Carving Bench. Picks are chosen from what each Amazon listing states, not from hands-on tests. Method: https://carvingbench.com/how-we-pick

Once you move from a knife to gouges, the work has to be held so both hands can stay on the tool and behind the edge. A wood carving vise does that and lets you turn the piece to a new angle without unclamping it. There are three main types. A faceplate carving vise screws to the base of the carving through a round plate and swivels and tilts on an arm: the work is fully exposed on every side except the bottom, which suits figures, busts and in-the-round carving. A patternmaker's vise has jaws that rotate and tilt, so it holds odd shapes, boards and relief panels. Small ball joint swivel vises clamp to a table edge and suit small figures and detail work. Check weight and mounting: a heavy cast vise needs a solid bench, and clamp-on models are limited by bench thickness. This guide compares seven vises by stated size, construction and mounting. Everything comes from the listings; nothing here was tested.

## Picks

### 1. Woodriver Carving Vise

WoodRiver carving vise in cast iron and steel, about 13 lb 10 oz, with a 5 inch faceplate and a base that rotates 360 degrees and locks with a ring. Holds figures and busts screwed to the plate.

What the listing offers:
- 5 inch platen, about 3/8 inch thick, gives a wide base for screwing on a carving blank.
- Base rotates 360 degrees and locks with a lock ring, so the work turns without unclamping.
- Cast iron and steel construction at over 13 lb, made for the force of gouge and mallet work.

Limits to know:
- Bolts or screws to the bench, so it needs a solid, permanent spot.
- Holds only work that can take screws in its base, not panels held edge-on.

### 2. BMTURNING Carving Vise with 5" Faceplate, Mount your Carving Vice project with Confidence, for Woodworking Carving Tools.

BMTURNING carving vise with a 5 inch faceplate, cast iron and steel, 14 lb, and a single-lever action for changing position. A lower-priced alternative to the WoodRiver faceplate vise.

What the listing offers:
- 5 inch base plate with plenty of area for mounting a workpiece, per the listing.
- Single lever action for fast position changes while carving.
- 14 lb cast iron and steel build, and a pin wrench for the pivoting base is included.

Limits to know:
- Mounting screws are not included, as the spec sheet notes.
- Lesser-known brand than WoodRiver, and the manufacturer gives no tilt range.

### 3. Woodriver Patternmaker's Carving Vise

WoodRiver patternmaker's carving vise with 4-7/8 inch jaws and a body that swivels 360 degrees. Clamps irregular shapes, legs and panels at almost any angle.

What the listing offers:
- Holds work in jaws, so it needs no screw holes in the carving.
- 4-7/8 inch jaws and a 360 degree swivel body, stated for holding virtually any shape.
- Listed for table legs, a good sign for long pieces and relief panels on edge.

Limits to know:
- The most expensive vise in this guide by a wide margin.
- The listing gives no weight, jaw opening or mounting details.

### 4. Stanley 83-069M Maxsteel Multi-Angle Base Vise

Stanley Maxsteel multi-angle base vise with a swivel-ball head that locks in any position and an integral screw clamp. A small bench-top vise for small carvings and detail.

What the listing offers:
- Swivel-ball design gives infinite, lockable positioning, per the listing.
- Integral screw clamp attaches to most work surfaces without bolts.
- Low price from a major tool brand, a cheap way to try holding small work.

Limits to know:
- Listed for crafts, models and electronics: too small for gouge and mallet work.
- The product page gives no jaw width or opening.

### 5. Excel Ball Joint Swivel Vise

Excel ball joint swivel vise with rubber jaws, a bench clamp, 360 degree swivel and 90 degree tilt. A small hobby vise for whittled figures and detail work.

What the listing offers:
- Rubber jaws protect a finished or painted carving from marks.
- Swivels 360 degrees and tilts 90 degrees to bring each face of a small piece toward you.
- Clamps to the bench, so it sets up and comes off in seconds.

Limits to know:
- The listing leaves the jaw opening and clamp size blank, so capacity is unclear.
- A light hobby vise: it will not hold up to mallet work.

As an Amazon Associate I earn from qualifying purchases.