# How to Wood Carve Faces: Proportions, Cut Order and Common Mistakes

Source: https://carvingbench.com/blog/how-to-carve-a-face-in-wood
Published: 2026-10-12
Publisher: Carving Bench

To carve a face in wood, draw a centerline down the corner of a basswood block, mark the face in thirds (brow, bottom of the nose, chin), then cut in this order: brow and eye sockets, nose, mouth mound, cheeks, and the eyes last. Carving on the corner gives the nose and cheeks depth for free, and leaving the eyes until the end stops you cutting them too deep before the rest of the face is set. Below are the proportions to mark, the tools, the step-by-step order and the mistakes that most often ruin a first face.

## Wood, block size and tools for a first face

Basswood is the standard choice: soft, even and able to hold small details like eyelids and nostrils. A first face is easiest on the corner of a block about 1-1/2 x 1-1/2 inches square and 4 to 6 inches long, held so one long edge faces you. The corner becomes the line of the nose and the two sides become the cheeks, so the face has depth from the start. Larger faces, such as a wood spirit on a 2 x 4 or a branch, follow the same steps.

A detail knife with a short, pointed blade (about 1 to 1-1/2 inches) does most of the work. A small V-tool helps for the lines beside the nose and mouth, and small gouges, such as a #9 or #11 of 3 to 6 mm, cut eye channels and nostrils cleanly. Wear a thumb guard on the hand that pushes the blade: faces involve many small cuts toward the thumb.

[Compare detail and whittling knives](https://carvingbench.com/best/best-whittling-knife-for-beginners)

## Face proportions to mark before you cut

Most carvers use the classic proportions from drawing, then exaggerate them for caricature. Draw a centerline down the corner. Divide the face from hairline to chin into thirds: hairline to brow, brow to the bottom of the nose, and bottom of the nose to the chin. The eyes sit just below the brow line, roughly halfway down the whole head. The mouth sits about one third of the way from the bottom of the nose to the chin.

Across the face, the width is about five eye-widths: one eye-width between the eyes and one on each side. The corners of the mouth line up roughly with the pupils, and the bottom of the nose is about as wide as the space between the eyes. The ears, if the carving shows them, run from the brow line to the bottom of the nose. Mark these lines in pencil and redraw them every time cutting removes them.

## Step by step: the cut order for a face

1. Brow and eye sockets. Make a stop cut straight across the corner at the brow line, then cut a wedge up to it from below to create the shelf under the brow. Deepen the area on each side of the nose bridge where the eyes will sit: this channel should be deeper than seems right, because eyes sit well back from the brow and the nose.

2. Nose. Make a stop cut under the tip of the nose and remove a wedge below it, so the nose stands proud of the mouth area. Cut down each side of the nose from the eye channel to the nostril, keeping it wide at the base. Shape the wings of the nostrils with small cuts or a small gouge.

3. Mouth mound and cheeks. The mouth sits on a rounded mound, not a flat plane: round the area from below the nose to the chin like the side of a cylinder. Cut the lines from the sides of the nose to the corners of the mouth with a V-tool or knife, then lower the cheeks beside them. 4. Mouth. Mark the line between the lips, make a shallow stop cut and shape the upper and lower lip with small slicing cuts. 5. Chin and jaw. Round the chin and separate it from the neck with a stop cut.

6. Eyes. Only now draw the eyes on the rounded eye mounds. Cut a shallow stop cut along the upper and lower lid lines and remove tiny slivers from the eyeball surface toward each cut, so the eyeball curves back into the corners. Keep each eye a small, almond-shaped dome. 7. Hair, beard and eyebrows. Add these last with a V-tool or knife lines that follow the flow of the hair.

## Mistakes that ruin a first face

Flat faces. The commonest problem is a face that sits on one flat plane. A real face wraps around a curve: the eyes sit on the sides of the head, not the front. Carving on the corner of a block and rounding the mouth mound fixes most of this.

Eye sockets too shallow, eyes cut too early. Shallow sockets make eyes that bulge forward and look surprised. Cutting the eyes before the brow, nose and cheeks are finished means they get cut away or end up in the wrong place. Set the sockets deep, finish everything around them, then cut the eyes.

A nose that is too small. Removing wood is easy and adding it is impossible, and a nose that has been trimmed back a few times ends up tiny. Leave the nose large and full until the end, then refine it. Dull tools. Small cuts across the grain on cheeks and lips tear unless the edge is freshly stropped; if the wood fuzzes, strop before continuing.

[Strops to keep a detail knife cutting cleanly](https://carvingbench.com/best/best-strop-for-carving-knives)

## Practice routine and the next step up

Faces improve with repetition more than with any single tip. Carve several small faces on 1 x 1 inch or 1-1/2 x 1-1/2 inch sticks rather than one large one: each takes an hour or two, and you can compare them side by side. Some carvers carve a strip of only noses, then only eyes, to practice each feature in isolation.

Once a face on a corner works, try the same face on a flat surface for a relief, or carve a wood spirit on a piece of bark or a split branch, where the bark becomes the hair and beard. Caricature carving, with exaggerated noses and cheeks, is a forgiving next project because small asymmetries read as character.

[Basswood blocks in sizes for face practice](https://carvingbench.com/best/best-basswood-carving-blocks)

## Frequently asked questions

What is the easiest face to carve for a beginner? A simple caricature or wood spirit face on the corner of a 1-1/2 inch square basswood block. The corner gives the nose depth automatically, and exaggerated features hide small mistakes.

What knife is best for carving faces? A detail knife with a short, pointed blade of about 1 to 1-1/2 inches. A longer roughing knife removes the bulk, and a small V-tool and a small deep gouge make the lines and eye channels easier but are not essential.

How do you carve eyes in wood? Leave them until the brow, nose and cheeks are done. Draw an almond shape on a rounded eye mound, make shallow stop cuts along the lid lines and remove small slivers from the eyeball toward the cuts so it curves back at the corners.

How long does it take to carve a face? A small practice face on a stick takes one to two hours for most beginners. A detailed wood spirit or a larger bust can take several evenings.

## Gear guides for this topic

- https://carvingbench.com/best/best-whittling-knife-for-beginners
- https://carvingbench.com/best/best-wood-carving-gouge-set
- https://carvingbench.com/best/best-basswood-carving-blocks
- https://carvingbench.com/best/best-whittling-thumb-guard
