# How to Carve a Spoon: Steps, Tools and How Long It Takes

Source: https://carvingbench.com/blog/how-to-carve-a-spoon
Published: 2026-10-01
Publisher: Carving Bench

**Short answer:** A first spoon takes about 2 to 4 hours of carving, then 2 to 3 days of drying before the final cuts and the oil. You need three tools: an axe or hatchet to rough out the blank, a straight sloyd knife for the outside and a hook knife for the bowl. Carve green wood, stop when the spoon is about 95% done, let it dry, then finish it.

Spoon carving for beginners goes wrong in two places: the wood and the edge. Dry wood makes every cut hard, and a dull knife tears the fibers instead of slicing them. The steps below follow the order green wood carvers publish: split, axe, straight knife, hook knife, dry, final cuts, oil. Sizes come from named references and are given as ranges where they differ. Published times cover the whole spoon, not each step, so the time table says which figure comes from where.

## How long does it take to carve a spoon?

Plan one afternoon for the carving and most of a week before the spoon is in use. The carving time falls fast with practice. The waiting does not: a spoon carved green has to dry before the final cuts, and a drying oil has to cure.

| Stage | Time | Source |
| --- | --- | --- |
| Carving, first spoon | 2 to 4 hours | BeaverCraft spoon guide |
| Carving, a slow first attempt | About 9 hours | Anne of All Trades, on her own first spoon |
| Carving, with practice | Under 1 hour | BeaverCraft |
| Drying the carved spoon | 2 to 3 days. Sources range from a couple of days to two weeks | Anne of All Trades, David Fisher |
| Final cuts in dry wood | No published figure | - |
| Mineral oil | No cure. Usable once wiped dry | Standard practice |
| Pure tung oil | Light use after 7 to 10 days, full cure 15 to 30 days | Real Milk Paint |

Times as published by the sources named in the table. None is a test result.

## The three tools you need to start spoon carving

Three edges do the whole job, and each has one task. A saw to cut the branch to length and a pencil complete the kit. Keep a strop with polishing compound within reach: routine upkeep is the strop, not the stone.

- **Axe or hatchet.** Splits the branch and roughs out the blank. It takes off the bulk of the waste far faster than a knife can. A bought spoon blank replaces this tool.
- **Straight knife.** A sloyd knife shapes the handle, the neck and the back of the bowl. The Morakniv 106 has an 85 mm (3.3 in) blade, the 120 a 62 mm (2.4 in) blade.
- **Hook knife.** Hollows the bowl. The Morakniv 164 has a 55 mm single-edge blade in right-hand and left-hand versions. Buy the one for your carving hand.

[See what each spoon carving kit includes](https://carvingbench.com/best/best-spoon-carving-kit)

## Spoon carving steps, from green branch to finished spoon

Use a green closed-grain hardwood such as birch, cherry or maple. The [spoon wood chart](https://carvingbench.com/blog/wood-for-spoon-carving) lists the rest. Sizes in steps 1 to 7 follow the Australian Wood Review guide by Barton Chesworth, converted to inches. Work on a chopping block for the axe steps and seated for the knife steps.

1. Cut the wood. A branch 3 to 6 inches (80 to 150 mm) thick, sawn to about 10 inches (250 mm), gives a spoon 6 to 8 inches long. With a bought blank, start at step 4.
2. Split the piece through the pith, the center of the branch, with the axe and light mallet blows. Axe away the pith and the first growth rings. Leaving them in is a standard cause of cracks.
3. Axe the half into a flat rectangular blank: bark off, two faces flat. If you stop here, put the blank in a sealed plastic bag or the freezer.
4. Draw the spoon on the top face. The bowl takes about one third of the length and the handle two thirds. Keep the outline simple and flowing. A metal spoon you like works as a template.
5. Saw a stop cut on each side of the neck, stopping short of the line. Axe the waste beside the handle down to the cuts. The saw cuts keep a split from running into the bowl.
6. Carve to the line with the straight knife. Thin the handle and round the back of the bowl. Leave the neck at least 3/8 inch (10 mm) deep: it is the weakest point of the spoon.
7. Hollow the bowl with the hook knife: many shallow cuts across the grain. For an eating spoon stop at about 5/16 inch (7 to 8 mm) deep. The grips are in [how to use a hook knife](https://carvingbench.com/blog/how-to-use-a-hook-knife).
8. Thin the back of the bowl until the wall is even. Published targets run from 1/8 to 1/4 inch (3 to 6 mm) at the thinnest point. Stop at about 95% done.
9. Dry the spoon for 2 to 3 days in a paper bag with a handful of shavings, away from heat and sun. The bag slows the drying, and slow drying is what prevents cracks.
10. Make the final cuts in the dry wood with a freshly stropped knife, take the sharp edges off, then oil the spoon. Mineral oil needs no cure. Pure tung oil needs 7 to 10 days before light use.

## How to tell the spoon is done

There are two finish lines. The green stage ends at about 95%, when only a thin skin of wood is left to remove. The dry stage ends when the final cuts have gone over every surface. David Fisher's account of his own spoon stages gives the reason for the split: final cuts in dry wood leave a cleaner, more polished surface.

- No pencil line and no flat axe facets are left on the outside of the handle or the bowl.
- The bowl wall feels even when pinched between thumb and finger all the way around, with no thick spot at the tip.
- The bowl of an eating spoon is no deeper than about 5/16 inch (7 to 8 mm), the depth the Wood Review guide ties to mouth feel.
- After drying, the knife leaves smooth facets with no torn or fuzzy grain, and every edge has been eased.

[Choose an oil for the finished spoon](https://carvingbench.com/blog/food-safe-finish-for-carved-spoons)

## Usual failure 1: the bowl is carved too thin

The hook knife works on the inside and the straight knife on the back, and the two surfaces meet sooner than expected. Published targets for the wall stop at about **1/8 inch (3 mm)**. Below that there is no margin left for the final cuts in dry wood, and one more pass can break through. Set the inside depth first, then stop hollowing. Take the rest of the thickness off the back only, checking the wall by pinching it before every few cuts. If the spoon has to wait, keep it in the bag: uneven thickness is also a standard cause of cracks while drying.

## Usual failure 2: the handle is cut against the grain

A knife cuts cleanly downhill, with the grain. Run it uphill and the edge dives under the fibers, the cut gets hard and a long splinter lifts ahead of the blade. On a spoon the downhill direction changes at every curve. Cut from the wide end of the handle toward the narrow neck, and from the widest point of the bowl toward the neck from the other side. The two cuts meet at the bottom of the hollow. When the knife starts to dig, stop and cut from the opposite direction.

The neck also carries short grain when a curved spoon comes from a straight blank. Fine Woodworking's guide by Peter Galbert uses a natural crook for this reason: the fibers bend with the spoon, so long grain runs from the handle to the tip of the bowl. In straight wood, keep the neck thick. Repairs for a spoon that has already split are in [how to fix cracks in a wood carving](https://carvingbench.com/blog/how-to-fix-cracks-in-wood-carving).

## Is spoon carving hard?

It is physical work with a short list of causes when it feels too hard: dry wood, a dull edge, cuts that are too deep and cutting against the grain. Green wood cuts far more easily than dry, which is the main reason carvers work fresh branches. A sharp tool needs less force and is easier to control. Wear a glove on the holding hand and keep the path of the blade clear of that hand and your legs. The choice between fresh and dried wood is covered in [green wood vs dry wood for spoon carving](https://carvingbench.com/blog/green-wood-vs-dry-wood-spoon-carving).

## Quick answers

The short version of the page for anyone about to start spoon carving: the time it takes, the tools and the order of work.

- **How long does it take to carve a spoon?** About 2 to 4 hours of carving for a first spoon, then 2 to 3 days of drying before the final cuts.
- **How to start spoon carving?** Get a green branch of birch, cherry or maple, or a blank, plus a straight knife, a hook knife and a strop.
- **Is spoon carving hard?** Not in green wood with a sharp edge. Dry wood and dull tools are what make it hard.
- **What are the spoon carving steps?** Split, axe out the blank, shape the outside, hollow the bowl, dry, make the final cuts, oil.

## Gear guides for this topic

- https://carvingbench.com/best/best-spoon-carving-kit
- https://carvingbench.com/best/best-spoon-carving-hook-knife
- https://carvingbench.com/best/best-spoon-carving-blanks
- https://carvingbench.com/best/best-strop-for-carving-knives

## Sources

- [Australian Wood Review: The Green Wood Spoon](https://www.woodreview.com.au/how-to/the-green-wood-spoon)
- [David Fisher: Spoon Stages](https://davidffisher.com/2020/06/26/spoon-stages/)
- [BeaverCraft: How to Carve a Wooden Spoon](https://beavercrafttools.com/blogs/how-to-carve/how-to-make-a-wooden-spoon)
