# Wood Carving Ornaments: Easy Designs, Wood Sizes and Finishing

Source: https://carvingbench.com/blog/how-to-carve-wood-ornaments
Published: 2026-10-12
Publisher: Carving Bench

Carved wood ornaments are small, light pieces, usually 2 to 4 inches tall, whittled from a 1 x 1 inch basswood stick or cut flat from a 1/4 to 1/2 inch board and decorated with chip carving. The easiest are a whittled pine tree, a simple Santa or gnome, a star and a flat chip carved disc. Each takes one to three hours, so a set for gifts is realistic if you start in October. Below are eight designs, the wood and tools for each, how to add a hanger and how to paint or finish them.

## Wood and sizes for carved ornaments

Basswood is the standard ornament wood: light, soft, even and good for paint. Buy it as 1 x 1 inch or 1-1/4 x 1-1/4 inch sticks for whittled figures, and as boards 1/4 to 1/2 inch thick for flat ornaments. Butternut and white pine work for natural-finish pieces. Weight matters on a tree: a whittled figure of 3 to 4 inches in basswood hangs fine on a normal branch, while the same piece in a dense hardwood pulls the branch down.

Cutting several ornaments from one long stick is faster than starting each from a separate block. Carve the figure on the end of a 10 to 12 inch stick, using the rest as a handle, then saw it off when the carving is nearly done. This keeps your fingers away from the blade and gives a firm grip on a small piece.

[Basswood blocks and sticks by size](https://carvingbench.com/best/best-basswood-carving-blocks)

## 8 wood ornament designs, easiest first

1. Whittled pine tree: a cone shape on a 1 x 1 inch stick with rows of small curled or notched cuts for branches, about an hour. 2. Icicle or twisted drop: a long tapering spiral, cut by rotating the stick and taking repeated angled cuts. 3. Simple Santa: a 1 x 1 x 3 inch stick with a pointed hat, a face on the corner and a beard of V-cuts, two to three hours. 4. Gnome: a tall hat over a nose and beard, with no face to carve, so it is forgiving for beginners.

5. Snowman: two or three stacked rounded sections with a hat, easy to paint. 6. Flat star or snowflake: cut from a 3/8 inch board with a coping saw, then chip carved on the face. 7. Chip carved disc or rosette: a 3 inch round of 3/8 to 1/2 inch basswood with a six-petal rosette or triangle border. 8. Bird or cardinal: a small songbird shape carved in the round or flat-backed, painted red, a good test of shaping.

## Tools for carving ornaments

A fixed-blade whittling knife with a blade of about 1-1/2 inches handles almost every whittled ornament; a smaller detail knife helps for faces and eyes. Flat chip carved ornaments need a chip carving knife and, for a clean outline, a coping saw or scroll saw. A small V-tool is optional for beards, hair and branch lines.

Small pieces mean many cuts close to the thumb, so wear a thumb guard or a cut-resistant glove on the holding hand. Keep the blade freshly stropped: small cross-grain cuts on beards and hat brims tear when the edge is even slightly dull, and a torn surface shows badly under paint.

[Compare whittling knives for small figures](https://carvingbench.com/best/best-whittling-knife-for-beginners)

## Step by step: a whittled Santa ornament

1. Take a 1 x 1 inch basswood stick about 10 inches long and turn it so a corner faces you. Mark the figure on the top 3 inches: hat brim about 1 inch down, the nose just below it on the corner, and the bottom of the beard about 2-1/2 inches down. 2. Make a stop cut all around at the hat brim and shape the hat to a point above it, rounding the corners.

3. Below the brim, cut in on each side of the corner to leave the nose standing proud, and remove a small wedge under the nose. 4. Shape the beard into a rounded point and add flowing V-cuts or knife lines for hair. 5. Round the body below the beard and make a stop cut where it ends. 6. Saw the figure off the stick, round the base, and drill a hole for the hanger at the tip of the hat. Paint: red hat and coat, white trim and beard, flesh tone on the face, a dot for each eye.

## Hangers, paint and finish

For a hanger, drill a 1/16 inch hole through the top of the piece and thread fine cord, twine or ribbon, or twist in a small screw eye. Drill before painting so the paint does not chip, and place the hole so the ornament hangs straight: on figures, just behind the top center of the head or hat.

Acrylic craft paint thinned with water to a wash lets the grain and cuts show through and is the usual choice for whittled ornaments. Paint the lightest colors first. Once dry, an antiquing wax or a thin coat of a dark-tinted finishing wax settles into the cuts and softens bright colors; buff with a soft cloth. For natural wood, a coat of Danish oil or a paste wax brings out the grain without changing the color much. Sign and date the bottom with a fine pen: carved ornaments become keepsakes.

## Frequently asked questions

What is the best wood for carving Christmas ornaments? Basswood. It is light enough to hang on any branch, soft enough for small detail with a knife and takes acrylic paint evenly. Butternut and white pine are good when you want a natural-wood look.

How big should a carved ornament be? Most are 2 to 4 inches tall. Whittled figures are usually carved from 1 x 1 inch stock, and flat ornaments from 1/4 to 1/2 inch boards about 3 inches across.

How do you hang a wooden ornament? Drill a 1/16 inch hole through the top and thread cord or ribbon, or twist in a small screw eye. Drill before painting and position the hole so the piece hangs straight.

How long does it take to carve an ornament? A whittled tree or icicle takes about an hour. A Santa or gnome takes two to three hours for a beginner, plus painting time.

## Gear guides for this topic

- https://carvingbench.com/best/best-basswood-carving-blocks
- https://carvingbench.com/best/best-whittling-knife-for-beginners
- https://carvingbench.com/best/best-chip-carving-knife
- https://carvingbench.com/best/best-whittling-thumb-guard
