Wood Carving Ornaments: Easy Designs, Wood Sizes and Finishing
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Gear for this job
All 7 picks comparedBeaverCraft BW19 Basswood Carving Blocks
See price on AmazonSee it on AmazonJyongmer Basswood Carving Blocks, 30 Pcs
See price on AmazonSee it on AmazonMANCHAP basswood blocks 6 x 2 x 2 in, 10 pack
See price on AmazonSee it on Amazon

Carved wood ornaments are small, light pieces, usually 2 to 4 inches tall, whittled from a 1 x 1 inch basswood stick or cut flat from a 1/4 to 1/2 inch board and decorated with chip carving. The easiest are a whittled pine tree, a simple Santa or gnome, a star and a flat chip carved disc. Each takes one to three hours, so a set for gifts is realistic if you start in October. Below are eight designs, the wood and tools for each, how to add a hanger and how to paint or finish them.
Wood and sizes for carved ornaments
Basswood is the standard ornament wood: light, soft, even and good for paint. Buy it as 1 x 1 inch or 1-1/4 x 1-1/4 inch sticks for whittled figures, and as boards 1/4 to 1/2 inch thick for flat ornaments. Butternut and white pine work for natural-finish pieces. Weight matters on a tree: a whittled figure of 3 to 4 inches in basswood hangs fine on a normal branch, while the same piece in a dense hardwood pulls the branch down.
Cutting several ornaments from one long stick is faster than starting each from a separate block. Carve the figure on the end of a 10 to 12 inch stick, using the rest as a handle, then saw it off when the carving is nearly done. This keeps your fingers away from the blade and gives a firm grip on a small piece.
8 wood ornament designs, easiest first
1. Whittled pine tree: a cone shape on a 1 x 1 inch stick with rows of small curled or notched cuts for branches, about an hour. 2. Icicle or twisted drop: a long tapering spiral, cut by rotating the stick and taking repeated angled cuts. 3. Simple Santa: a 1 x 1 x 3 inch stick with a pointed hat, a face on the corner and a beard of V-cuts, two to three hours. 4. Gnome: a tall hat over a nose and beard, with no face to carve, so it is forgiving for beginners.
5. Snowman: two or three stacked rounded sections with a hat, easy to paint. 6. Flat star or snowflake: cut from a 3/8 inch board with a coping saw, then chip carved on the face. 7. Chip carved disc or rosette: a 3 inch round of 3/8 to 1/2 inch basswood with a six-petal rosette or triangle border. 8. Bird or cardinal: a small songbird shape carved in the round or flat-backed, painted red, a good test of shaping.
Tools for carving ornaments
A fixed-blade whittling knife with a blade of about 1-1/2 inches handles almost every whittled ornament; a smaller detail knife helps for faces and eyes. Flat chip carved ornaments need a chip carving knife and, for a clean outline, a coping saw or scroll saw. A small V-tool is optional for beards, hair and branch lines.
Small pieces mean many cuts close to the thumb, so wear a thumb guard or a cut-resistant glove on the holding hand. Keep the blade freshly stropped: small cross-grain cuts on beards and hat brims tear when the edge is even slightly dull, and a torn surface shows badly under paint.
Step by step: a whittled Santa ornament
1. Take a 1 x 1 inch basswood stick about 10 inches long and turn it so a corner faces you. Mark the figure on the top 3 inches: hat brim about 1 inch down, the nose just below it on the corner, and the bottom of the beard about 2-1/2 inches down. 2. Make a stop cut all around at the hat brim and shape the hat to a point above it, rounding the corners.
3. Below the brim, cut in on each side of the corner to leave the nose standing proud, and remove a small wedge under the nose. 4. Shape the beard into a rounded point and add flowing V-cuts or knife lines for hair. 5. Round the body below the beard and make a stop cut where it ends. 6. Saw the figure off the stick, round the base, and drill a hole for the hanger at the tip of the hat. Paint: red hat and coat, white trim and beard, flesh tone on the face, a dot for each eye.
Hangers, paint and finish
For a hanger, drill a 1/16 inch hole through the top of the piece and thread fine cord, twine or ribbon, or twist in a small screw eye. Drill before painting so the paint does not chip, and place the hole so the ornament hangs straight: on figures, just behind the top center of the head or hat.
Acrylic craft paint thinned with water to a wash lets the grain and cuts show through and is the usual choice for whittled ornaments. Paint the lightest colors first. Once dry, an antiquing wax or a thin coat of a dark-tinted finishing wax settles into the cuts and softens bright colors; buff with a soft cloth. For natural wood, a coat of Danish oil or a paste wax brings out the grain without changing the color much. Sign and date the bottom with a fine pen: carved ornaments become keepsakes.
Frequently asked questions
What is the best wood for carving Christmas ornaments? Basswood. It is light enough to hang on any branch, soft enough for small detail with a knife and takes acrylic paint evenly. Butternut and white pine are good when you want a natural-wood look.
How big should a carved ornament be? Most are 2 to 4 inches tall. Whittled figures are usually carved from 1 x 1 inch stock, and flat ornaments from 1/4 to 1/2 inch boards about 3 inches across.
How do you hang a wooden ornament? Drill a 1/16 inch hole through the top and thread cord or ribbon, or twist in a small screw eye. Drill before painting and position the hole so the piece hangs straight.
How long does it take to carve an ornament? A whittled tree or icicle takes about an hour. A Santa or gnome takes two to three hours for a beginner, plus painting time.
What you need for this
- See price on AmazonAmazon
BeaverCraft BW19 Basswood Carving Blocks
From Best Basswood Carving Blocks: Sizes, Pack Counts and Price per Block
- See price on AmazonAmazon
Flexcut KN13 detail knife, 1.5 in blade
From Best Whittling Knife for Beginners: Fixed-Blade Carvers Compared
- See price on AmazonAmazon
Flexcut KN15 chip carving knife, 1 in blade
From Best Chip Carving Knives: Cutting Knife, Stab Knife and Starter Sets
- See price on AmazonAmazon
Ringsun RS40 leather thumb guard, full grain
From Best Whittling Thumb Guards and Safety Tape for Carving