Tool
Sharpening Angle Chart for Carving Knives, Hook Knives, Gouges and V-Tools
One row per tool, with the angle as its maker or a standard reference states it, and whether that figure is per side or for the whole edge.
Short answer
Most published carving edges fall between 12 and 28 degrees. Thin whittling knives are quoted at 12 to 20 degrees inclusive. Morakniv lists 26 to 28 degrees for its sloyd knives and 24 to 26 for its hook knife. Pfeil grinds gouges from 17 degrees for softwood to 25 for hardwood. A chip carving knife is held about 10 degrees off the stone.
Per side or inclusive
Per side is the angle between one face and the center of the blade. Inclusive, also called the edge angle, is the whole wedge: twice the per side figure on a symmetrical knife.
Sharpening angles by tool
Pick a tool to see only its rows and what to watch for. A lower angle cuts with less force and dulls or chips sooner. A higher angle lasts longer and needs more force.
| Tool | Bevel form | Published angle | Stated as | Source |
|---|---|---|---|---|
| Whittling and detail knife (thin flat grind) | one flat bevel per side, no secondary bevel | 12 to 20 degrees | inclusive | Carving is Fun (hobby reference) |
| Whittling knife, BeaverCraft | flat bevel | 20 degrees, "ideal for carving soft wood" | "bevel angle", basis not stated | BeaverCraft glossary |
| Sloyd knife (Scandinavian grind) | one wide flat bevel per side | 26 to 28 degrees (Morakniv 106 and 120). One hobby reference quotes 22 to 23 degrees for Scandinavian grinds | edge angle, inclusive | Morakniv product pages, Carving is Fun |
| Hook knife (spoon knife) | single bevel on the outside, flat inside | 24 to 26 degrees (Morakniv 164) | edge angle, inclusive | Morakniv product page |
| Chip carving cutting knife | flat bevel per side | about 10 degrees to the stone | per side | Woodworkers Institute |
| Chip carving stab knife | bevel per side | 30 degrees on each side | per side | Woodworkers Institute |
| Gouges | outside bevel, optional short inner bevel | 17 degrees (softwood) to 25 degrees (hardwood) | bevel angle | Pfeil guidance quoted by Classic Hand Tools |
| Gouges, second source | outside bevel plus inner bevel | 15 to 20 degrees outside, 5 to 10 degrees inside | cutting angle | Woodcarving Illustrated, "Tuning Your Tools" |
| Carving chisels | bevel both sides | 15 to 20 degrees | cutting angle | Woodcarving Illustrated |
| Skew chisel | bevel both sides, end skewed | bevels as chisels, end skewed at about 45 degrees | cutting angle | Woodcarving Illustrated |
| V-tool | two chisel wings meeting at a keel | each wing as a chisel: 17 to 25 degrees | bevel angle | Pfeil guidance (one range for all its tools) |
| Carving axe | per maker | no published figure found | - | Gransfors Bruk product page lists none |
Sharpening angles for hand wood carving tools as published by makers and standard carving references, checked October 2026. Kitchen and pocket knives are not covered. Inclusive means the whole edge, both sides together. The small drawings are schematic: knives in cross-section with the edge down, gouges and chisels from the side, the skew from above, the V-tool end on.
How to read this chart
Every figure is a published one, shown the way its source states it. The chart does not average figures and does not convert between per side and inclusive, because that would produce numbers no maker publishes.
- Softwood or hardwood: the only published adjustment is for gouges and chisels. Pfeil gives 17 degrees for softwood and 25 for hardwood. Woodcarving Illustrated notes that carvers use bevels from 15 up to 30 degrees, low for softwood and high for hardwood. No maker publishes a softwood and hardwood figure for knives.
- V-tool profile angles are a different number: the angle between the wings, not the bevel. They run from 45 to 90 degrees, with 60 the most useful.
- A lower angle cuts with less force and dulls or chips sooner. A higher angle lasts longer and needs more force.
- Carving knives are sharpened with the whole bevel flat on the stone. Keep the angle the maker ground and do not add a secondary bevel.
- Carving axe: keep the factory bevel. No degree figure is given on this page.
Routine upkeep is the strop, not the stone. The motion and the schedule are in how to strop a carving knife.
Note.Makers grind different angles. If your tool's maker publishes a figure, use it. Strop and sharpen with the edge moving away from the hand that holds the stone or strop.
Read next
Kitchen and pocket knife angles are on our sister site, stoneandstrop.com.
Sources
- Morakniv 106: sloyd knife edge angle
- Morakniv 120: sloyd knife edge angle
- Morakniv 164: hook knife edge angle
- BeaverCraft, knife bevel: whittling knife bevel
- Classic Hand Tools, quoting Pfeil: gouges, chisels and V-tools
- Woodcarving Illustrated, Tuning Your Tools: gouges and chisels
- Woodworkers Institute, getting started with chip carving: chip carving knives
- Carving is Fun, knife sharpening: thin whittling knives and Scandinavian grinds
- Flexcut, sharpening your tools: stropping guidance, gives no degree figure