Tool

Wood for Carving Chart: Hardness by Species and What Each Wood Is Good For

Find your wood, or filter by the style you want to carve. Hardness is the Janka figure for dry wood. The verdicts follow the rule printed under the chart.

Where to start, by carving style

Wood for carving chart: 36 species

Have a piece of wood? Type its name. Want to carve a spoon or a chip carving board? Pick the style and the chart keeps the woods that suit it, softest first. The print button prints the whole chart, whatever is filtered on screen.

How to read the chart

Janka hardness is the force, in pounds-force (lbf), needed to press a 0.444 inch steel ball halfway into the wood, measured at 12% moisture. A lower number cuts more easily. The figures are typical values and vary from one sample to the next. They describe dry wood: green wood of the same species cuts far more easily, which is why the harder spoon woods are carved fresh.

Each figure is the one on the species page of the Wood Database. Where the Janka table on Wikipedia, whose figures are of USDA origin, gives a different number, the row shows the range between the two. That is the case for balsa, Honduran mahogany, northern red oak, white oak and shagbark hickory. The bar under each number is the hardness on a scale that ends at 2,000 lbf.

The rule behind yes, maybe and no

  • Whittling means a dry block held in the hand and cut with a knife. Yes: up to about 600 lbf and known to cut cleanly. Maybe: up to 600 lbf with a drawback (fuzzy, crushes, dents, coarse grain) or a softwood other than the two white pines, or 600 to about 1,050 lbf, or a harder closed-grain wood that is normally whittled green. No: ring-porous hardwoods above 1,050 lbf and pine with hard resinous bands. One override: European lime is a yes at 700 lbf because the Wood Database rates it among the most suitable woods for hand carving.
  • Spoon carving means a spoon to eat or cook with, normally carved green. Yes: closed-grain hardwoods from about 590 lbf up. Maybe: hardwoods under 590 lbf, which carve easily but dent and wear, and woods normally sold only as dry carving stock (tupelo, mahogany). No: softwoods (resin or strong smell), balsa, and ring-porous hardwoods with large open pores (oak, ash, hickory, catalpa).
  • Chip carving means a flat dry board and a chip carving knife. Yes: the three standard chip carving woods (basswood, butternut, European lime). Maybe: other even-grained hardwoods from 350 to about 1,050 lbf and the two soft white pines. No: everything else, including stringy willow and cottonwood, coarse-grained catalpa, the other softwoods and anything above 1,050 lbf.
  • Relief carving means gouges on a clamped board, pushed by hand or struck with a mallet. Yes: hardwoods up to about 1,050 lbf that cut cleanly, the two white pines, and pear. Maybe: fuzzy or stringy woods (aspen, willow, cottonwood), paper birch (wild grain), softwoods other than the two white pines, and woods above 1,050 lbf, which call for a mallet. No: balsa, southern yellow pine, hickory.

Note.Verdicts follow the rule above. They are the usual hobby consensus applied to hardness and grain, not the result of testing. The no for oak and ash under spoon carving is about their open pores and common practice only.

The chart has no toxicity or allergy column. For dust and allergy questions see the Wood Database chart of wood allergies and toxicity.

Short answers

Can you whittle pine?

Eastern white pine and sugar pine, yes. Southern yellow pine and most construction lumber, no. More in can you whittle pine.

Can you whittle oak?

Not with a knife: oak runs 1,220 to 1,360 lbf and is open-pored. Oak is carved with gouges and a mallet.

Is cedar good for carving?

Cedar is soft enough but dents and is strongly aromatic. Not for spoons.

Is maple good for spoon carving?

Yes, carved green. The soft maples, silver and red (700 to 950 lbf), are easier than hard maple (1,450 lbf).

Is birch good for spoon carving?

Yes, birch is a standard green spoon wood.

Is poplar good for carving?

Yellow poplar is workable, a step harder than basswood, and soft for a spoon in daily use.

Can you whittle hardwood?

Basswood, butternut and alder are hardwoods. "Hardwood" is a botanical group, not a hardness figure.

What is the softest wood for carving?

Balsa is the softest but crushes. Basswood is the softest that holds detail.

Read next

Sources

Hardness figures and working notes: the Wood Database, species pages and its Janka hardness article. Second figures for the ranges: the table in Wikipedia's Janka hardness test article. Wood varies from piece to piece, so treat every figure as typical, not exact.