How to Wood Carve With a Dremel: Bits, Speeds and a First Project
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Gear for this job
All 7 picks comparedCAELUM Carbide Rotary Burr Set, 3 Pcs
See price on AmazonSee it on AmazonEZARC Tungsten Carbide Rotary Burr Set, 3 PCS
See price on AmazonSee it on AmazonDremel 117HP Max Life Carving Bit, 2-Pack
See price on AmazonSee it on Amazon

To carve wood with a Dremel, clamp the piece, rough out the shape with a coarse carbide burr at medium speed, then switch to smaller bits for refining and detail and finish with sanding drums or abrasive points. Let the bit do the cutting with light pressure and many passes; pushing hard causes burning, chatter and bits that skate off the line. This page covers which bits to fit, the speeds that work in wood, how to hold the tool and the work, a step-by-step first project and the safety gear rotary carving needs.
What you need to start carving with a Dremel
Any variable-speed Dremel or similar rotary tool will carve wood. A corded model is better than a small cordless one for anything beyond light detail, because carving keeps the motor loaded for long stretches. The tool takes 1/8 inch (3.2 mm) shank bits in its standard collet, and almost every carving bit sold for rotary tools uses that shank.
Beyond the tool, a useful starter kit is short: one or two coarse open-tooth carbide burrs for roughing, a few small high speed steel or fine carbide cutters for shaping, a couple of tiny engraving cutters or diamond points for detail, and sanding drums or flap wheels for smoothing. Add a way to hold the work (a vise or clamps), safety glasses, a dust mask rated N95 or better and, ideally, a dust extractor or shop vacuum near the work. A flex shaft attachment is optional but makes the handpiece much lighter and slimmer to hold for detail.
Which Dremel bits to use for wood, by job
Roughing out: coarse carbide burrs with open, sharp teeth, often sold as the Saburrtooth style, remove wood fastest and do not clog with dust. A flame or tapered shape forms the outline and a sphere hollows. Use these to get within about 1/8 inch of the final surface.
Shaping: Dremel's high speed steel carving cutters (the 100 series, such as the 114, 116 and 117) and fine double-cut carbide burrs remove less per pass and leave a smoother surface. They are good for rounding forms, cutting grooves and refining feather or fur groups. Steel cutters dull faster than carbide in hardwoods, so treat them as consumables.
Detail and texture: small engraving cutters around 1/32 to 3/32 inch, diamond points and small ruby or stone points add eyes, hair lines, feather barbs and lettering. Smoothing: sanding drums, bands and flap wheels in 120 to 220 grit take out tool marks before finishing. Avoid the cut-off wheels for carving; they are thin, brittle and can shatter if twisted in a groove.
Dremel speed settings for carving wood
There is no single correct speed, but the working range most carvers use is medium to high: roughly 15,000 to 25,000 RPM for carbide burrs and steel cutters in wood, and higher for small engraving bits and diamond points, which cut best when spinning fast. On a Dremel with a 1 to 10 dial, that is about settings 5 to 8 for most carving.
Read the wood rather than the dial. Brown or black burn marks and a smell of scorching mean the speed is too high for the bit, the pressure is too heavy, or the bit is clogged. Chatter, a bouncing bit and a rough, torn surface mean the speed is too low or you are taking too big a bite. Soft woods like basswood clog bits faster than hardwoods, so clean the teeth with a brass brush often. Large coarse burrs need lower speeds than small detail bits; check the maximum RPM printed on any bit's packaging and never exceed it.
How to hold the Dremel and the wood
Hold the tool like a pen for detail and like a dagger or a hammer handle for roughing, with your hand close to the bit. Brace the heel of the hand or a finger on the work or the bench so the bit cannot jump. Take light, short passes and move steadily: a bit held still in one spot digs a hole or burns.
A spinning bit pulls itself along the surface in one direction. If the bit grabs and runs off the line, change the direction of your stroke or approach the edge from the other side, so the bit is cutting into the wood rather than rolling along it. Climb cuts that let the bit run are the main cause of slips across a finished surface.
Clamp the work whenever you can. A carving vise or a small swivel vise holds the piece at the angle you need and keeps both hands on the tool. When a small piece must be held in the hand, wear a cut-resistant glove on the holding hand and keep fingers out of the path of the bit, especially behind thin edges.
Step by step: a first Dremel carving
1. Choose a soft, even wood such as basswood, about 2 x 2 x 4 inches, for a simple bird, fish or leaf. 2. Draw the outline on two sides (side view and top view) with a pencil and mark the centerline. 3. Cut away the bulk outside the outline with a coping saw or band saw if you have one; it is faster than grinding it all.
4. Fit a coarse carbide burr and rough the shape to within about 1/8 inch of the final surface, working around the piece so it stays balanced. Redraw the centerline whenever it disappears. 5. Change to a smaller steel cutter or fine carbide burr and refine the form: round the body, define the head, cut the major grooves. 6. Use a small engraving bit or diamond point for eyes, the line between wing and body, and texture.
7. Smooth with a 120 grit sanding drum, then 180 or 220 by hand or with finer drums. Blow or vacuum off the dust between grits so you can see remaining marks. 8. Finish with oil, wax or paint. Basswood takes acrylic paint well; for a natural look, a penetrating oil darkens it only slightly.
Dust, noise and safety
Rotary carving makes fine dust, not chips, and that is the main hazard. Wear a mask rated N95 or better as a minimum, and put a shop vacuum hose or a small dust collector next to the work. Fine wood dust from some species, including many exotics, is a known irritant and sensitizer. Wear safety glasses or a face shield: bits throw chips and, occasionally, broken fragments.
Tie back long hair and keep sleeves and glove cuffs away from the spinning bit and collet. Unplug the tool or remove the battery before changing bits, tighten the collet fully on the shank, and never use a bit with a bent shank: it will whip at speed. Let the motor rest if the housing gets hot during long roughing sessions.
Frequently asked questions
Can you carve wood with a regular Dremel? Yes. Any variable-speed Dremel or similar rotary tool with a 1/8 inch collet will carve wood with the right bits. A higher wattage corded model handles long roughing better, and a flex shaft makes detail easier, but neither is required to start.
What is the best Dremel bit for wood carving? For removing wood fast, a coarse open-tooth carbide burr in a flame or ball shape. For shaping and detail, Dremel's high speed steel carving cutters and small engraving cutters. Most carvers end up with two or three roughing burrs and a handful of detail bits rather than a big kit.
Why is my Dremel burning the wood? The speed is too high for that bit, the pressure is too heavy, the bit is clogged or the bit is dull. Lower the speed a little, lighten your pressure, clean the teeth with a brass brush and keep the tool moving.
Is power carving easier than hand carving? It removes wood with less hand strength and handles hardwoods that are slow with a knife, but it is noisy and dusty and still needs control. Many carvers rough out with a rotary tool and finish detail with knives and gouges.
What you need for this
- See price on AmazonAmazon
CAELUM Carbide Rotary Burr Set, 3 Pcs
From Best Dremel Wood Carving Bits: Carbide Burrs, HSS Cutters and Kits
- See price on AmazonAmazon
Proxxon 38644 Die-Cast Aluminum Power Carver MOS
From Best Electric Wood Carving Tools: Power Carvers, Power Chisels and Flex Shafts
- See price on AmazonAmazon
Woodriver Carving Vise
From Best Wood Carving Vises: Faceplate Carving Vises, Patternmaker's and Ball Joint
- See price on AmazonAmazon
Schaaf whittling gloves, EN388 Level 5, Medium
From Best Whittling Gloves: Cut-Resistant Gloves by Cut Level and Size