How-to
How to Strop a Carving Knife and How Often to Do It
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Short answer
Lay the bevel flat on a leather strop loaded with polishing compound and pull the knife away from its edge with light pressure, then flip it and repeat. Published routines run from 5 to 30 strokes. Strop when the knife starts to drag in the cut, which carvers commonly put at every 10 to 30 minutes of carving.
Gear for this job
All 6 picks comparedBacher leather strop 12.6 in, 4 compounds and balm
See price on AmazonSee it on AmazonBeaverCraft LS6P1 double-sided paddle strop, 14 in
See price on AmazonSee it on AmazonBeaverCraft LS5P1 Carving Strop Kit
See price on AmazonSee it on Amazon

This is for whittling knives, detail knives and sloyd knives: the ones with one flat bevel per side and no secondary bevel. Stropping is the routine upkeep for these tools. The stone only comes out when the edge is chipped or rounded. Two things decide the result: the bevel stays flat on the leather for the whole stroke, and the edge always trails. Stroke counts differ from one source to the next, so each count below is given with the source that publishes it. Kitchen and pocket knife sharpening is a different job and is covered on our sister site, stoneandstrop.com.
How to strop a carving knife, step by step
You need a leather strop, polishing compound and a few minutes. The bevel is the part that touches the leather. On a thin whittling or detail knife the blade lies almost flat on the strop. On a sloyd knife the spine comes up until the wide bevel sits flat. Published angles for each knife type are in the sharpening angle chart.
- 1
Rub compound onto the leather like a crayon until it leaves a thin, even film. Carving Junkies notes that 1 application can last for months, so this is not a job for every session.
- 2
Set the strop flat on the bench, or hold it by the handle with your fingers behind the working surface. The edge must move away from the hand that holds the strop.
- 3
Lay the bevel flat on the leather at the near end. Use light pressure. Carving Junkies and Schaaf Tools both warn that heavy pressure works against you: control matters more than force.
- 4
Pull the knife along the strop spine first, edge trailing, and cover the edge from heel to tip in 1 stroke. Never push the edge into the leather.
- 5
At the end of the stroke, stop and lift the blade straight up off the leather. Do not roll it over its edge to turn it.
- 6
Flip the knife and make the same stroke on the other side. One routine quoted by Carving Junkies: 10 strokes per side, then 9, then 8, and so on down to 1.
- 7
Wipe the blade and test it on the end grain of a basswood scrap. If it still drags, run the routine 1 more time before reaching for a stone.
How many strokes per side?
No maker publishes a required number. Flexcut says only to strop until the sharpness is restored. Hobby sources do give counts, and they do not agree. That tells you the count matters less than a flat bevel and light pressure. Pick one routine and keep the strokes equal on both sides.
| Source | Strokes | When |
|---|---|---|
| Carving Junkies, countdown | 10 per side, then 9, 8 and so on down to 1 | Full session before carving |
| Carving Junkies, short version | 5 per side, working down to 1 | Full session before carving |
| Carving Junkies, touch-up | 10 to 15 per side | Every half hour or so |
| Schaaf Tools | 20 to 30, flipping every 5 to 10 strokes | Before, during and after carving |
| Flexcut | No count: until sharpness is restored | When the tool starts to drag |
How often do you need to strop a whittling knife?
Flexcut's rule is the simplest: strop when the tool begins to feel as if it is dragging through the cut. Carvers commonly quote every 10 to 30 minutes of carving. That is a habit, not a maker figure. Carving Junkies describes a touch-up every half hour or so, and Schaaf Tools advises stropping before, during and after a session.
The wood changes the interval. Basswood, at 410 lbf on the wood for carving chart, is easy on an edge. Harder woods are not: Carving is Fun notes that oak dulls knives quickly. If a cut that was clean a few minutes ago now needs more push or leaves a dull, torn surface, strop then, whatever the clock says.
Which strop and compound to use
A flat leather strop with polishing compound is the standard setup. Woodcarving Illustrated specifies a flat, hard leather strop. Flexcut recommends its Gold polishing compound, and Carving is Fun uses green polishing compound. Carving Junkies lists leather as the usual surface, notes that cardboard, denim and wood are also used, and describes black compound as more abrasive than the other colors. Curved tools need a shaped strop: see how to sharpen carving gouges.
How to tell the edge is sharp again
Stop when the knife passes a cutting test, not when a count is reached. Four checks are published by the sources used here, and all of them take a few seconds.
- End grain: slice across the end grain of basswood. Carving Junkies treats a quick, clean cut there as the sign of a sharp knife.
- Cut surface: Schaaf Tools describes a sharp blade as one that slices cleanly and leaves a shiny cut on the wood.
- Bevel polish: a bevel that reflects like a mirror shows the strop reached the whole surface (Carving Junkies).
- Cutting angle: Flexcut checks the angle at which the tool starts to cut. If the blade has to be tipped up steeper than before to bite, the edge has rounded.
When to sharpen a whittling knife on a stone instead
Stones are for damage, not upkeep. Flexcut warns that sharpening stones are too coarse for routine maintenance and scratch the polish. Go to a stone when a full stropping routine no longer brings the edge back, or when the edge is nicked. Schaaf Tools names the sign to look for: small chips or glints of light along the edge.
One hobby reference, Carving is Fun, gives the sequence as 400 to 600 grit, then 800 to 1,000 grit, then the strop. The whole bevel stays flat on the stone, just as on the leather. The full method is in how to sharpen a whittling knife.
Note.Hold the knife edge-up under a lamp. A bright spot or line on the edge is a chip or a flat. Stropping will not remove it, so that knife needs a stone.
Why the edge gets rounded after stropping
A knife that cuts worse after stropping was lifted. When the spine rises during the stroke, or the blade is rolled over its edge at the turn, the leather wraps around the edge and rounds it. Carving Junkies lists three mistakes to avoid: moving the blade toward its cutting edge, rolling the edge instead of lifting straight up, and pressing too hard.
- Lifted spine: watch the bevel, not the edge, and keep it flat on the leather from the start of the stroke to the stop.
- Rolled turn: stop, lift straight up, turn the knife in the air and set the other bevel down.
- Edge rounded already: more stropping will not fix it. Reset the flat bevel on a stone, then strop.
Quick answers
Short answers on stropping and sharpening schedules. Counts and intervals are published habits from the sources named, not maker rules.
- How often do you need to sharpen whittling knives? On a stone, only when the edge is chipped or stropping stops working. On the strop, when the knife drags: commonly every 10 to 30 minutes of carving.
- When to sharpen a whittling knife? When a full stropping routine no longer restores a clean cut, or when you can see chips or glints of light on the edge.
- How to hone a whittling knife? Honing here means stropping: bevel flat on compound-loaded leather, edge trailing, light pressure, equal strokes on both sides.
- How long does a whittling knife last? None of the makers' pages read for this article gives a lifespan. Stropping only polishes the edge. Stones are what remove steel, so a knife kept up on the strop wears slowly.
What you need for this
- See price on AmazonAmazon
Bacher leather strop 12.6 in, 4 compounds and balm
- See price on AmazonAmazon
Sharp Pebble grooved stones, 400 and 1000 grit
From Best Sharpening Kits for Wood Carving Knives, Hook Knives and Gouges
- See price on AmazonAmazon
Flexcut KN13 detail knife, 1.5 in blade
From Best Whittling Knife for Beginners: Fixed-Blade Carvers Compared