Chart
Chip Carving Practice Patterns: Six Beginner Sheets and Free Pattern Sources
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Short answer
Start with a row of three-cut triangles on a 4 mm grid, then carve facing rows, a zigzag border, diamonds, four-chip squares and a six-petal rosette, in that order. Each sheet is plain geometry you can rule onto 3/8 inch basswood in a few minutes. Free printable PDFs come from Santa Clara Valley Carvers, READ N TRY and Lora Irish, listed below.
Gear for this job
All 6 picks comparedFlexcut KN15 chip carving knife, 1 in blade
See price on AmazonSee it on AmazonFlexcut KN115 chip carving set, 3 knives
See price on AmazonSee it on AmazonBeaverCraft C6 chip carving knife, 1 in
See price on AmazonSee it on Amazon

A practice pattern is a grid with some of its triangles marked for cutting. What decides whether it teaches anything is the size of the grid and the order of the motifs: small chips first, shared edges next, curves last. The six sheets on this page are Carving Bench's own layouts, described so you can rule them with a pencil and a ruler or mark them on a printed blank grid. Finished designs by other carvers are not reproduced here. They are listed by name so you can download them from the people who drew them.
Six chip carving practice patterns, in carving order
Carve the sheets in this order. Each one adds a single new difficulty, so a ragged chip tells you which skill to go back to. The grid sizes are the two used across this site, 4 mm and 1/4 inch.
| Sheet | Motif | What it practices | Grid |
|---|---|---|---|
| 1 | One row of three-cut triangles, points up | The basic chip at a steady knife angle | 4 mm, then 1/4 in |
| 2 | Two rows of triangles, points facing | Cuts that meet cleanly on a shared line | 4 mm, then 1/4 in |
| 3 | Zigzag border: triangles alternating up and down | Turning the board, even spacing | 4 mm, then 1/4 in |
| 4 | Diamonds: two triangles base to base | Mirror cuts and sharp ridges | 4 mm, then 1/4 in |
| 5 | Four-triangle squares: a square split by both diagonals | Four chips meeting at one center point | 1/4 in, or 2 x 2 squares of the 4 mm grid |
| 6 | Six-petal rosette drawn with a compass | Curved cuts, the first chip that is not straight | Circle radius 5 squares: 20 mm or 1-1/4 in |
How to draw chip carving patterns on a grid
Every sheet starts from the same ruled grid. You need a hard pencil, a ruler with clear marks, a small T-square and, for sheet 6, a compass.
- 1
Rule the grid. Mark every 4 mm (or 1/4 inch) along one edge of the board, then draw the crossing lines with the T-square. Three rows of squares are enough for sheets 1 to 4.
- 2
Sheet 1: in one row, tick the top line halfway across each square, 2 mm in on the 4 mm grid. Join each tick to the two bottom corners of its square. Every square now holds one triangle, point up.
- 3
Sheet 2: draw sheet 1 in the lower row, then the same triangles upside down in the row above, so each pair of points meets on the shared line.
- 4
Sheet 3: draw point-down triangles hanging from the top line and point-up triangles standing on the bottom line, shifted half a square sideways. The uncut wood left between them reads as a zigzag.
- 5
Sheet 4: draw a point-up triangle in the upper row and a point-down triangle directly under it, both bases on the middle line. Each pair makes one diamond with a ridge across its middle.
- 6
Sheet 5: draw both diagonals of a square. That gives four triangles whose points meet in the center. Leave one plain square between carved squares.
- 7
Sheet 6: set the compass to 5 squares and draw a circle. Keep the setting, put the point on the circle and swing an arc through the center from rim to rim. Move the point to where the arc met the rim and repeat until six petals appear.
Why easy chip carving patterns start on a 4 mm grid
Murray Taylor's beginner course for Woodworkers Institute starts on a 4 mm grid and has beginners master it before trying 5 mm, because the pyramid-shaped chip from a 5 mm grid has twice the volume and is much harder to remove. Chip volume grows with the cube of the grid size, so the same arithmetic puts a 1/4 inch chip at about four times a 4 mm one. Bigger chips need a deeper cut and a keener edge. If they tear, drop back a size and strop the knife.
| Grid | Chip volume against 4 mm | When to use it |
|---|---|---|
| 4 mm | 1x | First sheets. The beginner size in the Woodworkers Institute course |
| 5 mm | about 2x | Once 4 mm chips pop out whole |
| 1/4 in (6.35 mm) | about 4x | Larger motifs. READ N TRY practice boards use cells of 3/16 to 1/4 in |
| 1/3 in (8.5 mm) | about 9.5x | Bold motifs. Lora Irish offers a blank grid in this size |
Where to find chip carving patterns: free printable PDFs
These are the free pattern pages this site opened in October 2026. The designs belong to the people who drew them, so they are named here and not copied. Download each one from its source and read that site's terms before sharing the file.
| Source | What is free | Format |
|---|---|---|
| Santa Clara Valley Carvers (club site) | Two Supernova patterns by Roman Chernikov, round and square, 108 three-corner chips each | Scalable PDF |
| READ N TRY (readntry.com) | Small ornament patterns of 6 to 13 chips each, plus coaster and strop designs | Scalable, printable PDFs |
| Lora Irish (lsirish.com) | Blank 1/4 in and 1/3 in graph grids, a graphed pattern and a printable practice pattern | Printable pages inside her free tutorials |
| My Chip Carving (mychipcarving.com) | Practice board patterns from instructor Marty Leenhouts | Offered through a signup form |
Note.The Supernova chips are spaced apart so that no two share a sharp edge, which its designer gives as the reason it forgives beginner mistakes. At 108 chips it is a project, not a warm-up.
How to transfer a printed pattern to basswood
A printed pattern has to reach the wood at the right size. Print at 100 percent with scaling off, then measure ten squares: they should span 40 mm on the 4 mm grid or 2-1/2 inches on the 1/4 inch grid. Sand the board smooth first: Lora Irish's tutorial uses 320 grit. For the board see wood for chip carving. The basswood guide lists flat boards.
- Rule it directly. A hard pencil, a ruler and a small T-square put the grid straight onto the wood. Nothing to print or tape down.
- Trace through graphite paper. Tape the printout to the board along one edge, slide graphite paper under it and go over the lines.
- Stick the printout down. Removable spray adhesive fixes the printed pattern to the board for the time it takes to carve it.
- Heat transfer. READ N TRY describes moving laser printer toner onto the wood with an iron or a woodburning tool.
Chip carving border patterns built from the same sheets
A border is one sheet repeated along an edge. Count squares before you draw so the row ends on a whole chip: a 12 inch board holds 48 squares of 1/4 inch, and a 200 mm board holds 50 squares of 4 mm.
- Sawtooth. Sheet 1 run along the edge, points toward the middle of the board. One chip per square.
- Zigzag ribbon. Sheet 3. The two offset rows leave a raised zigzag between them.
- Diamond chain. Sheet 4 repeated, with one plain square between diamonds while your spacing is still uneven.
How to tell a practice sheet went well
Marty Leenhouts of My Chip Carving argues that repeating a pattern does not by itself make anyone better: each session needs focus and feedback on specific mistakes. So check every sheet against this list before starting the next one. A chip carving knife that drags will fail all four checks, whatever the pattern.
- Every chip came out whole, without prying. A chip that hangs on means the three cuts did not meet.
- The walls of each chip are flat and meet at one point at the bottom, with no steps or loose fibers.
- Ridges between neighboring chips are unbroken and the same width along the row.
- The cuts sit on the pencil lines, not beside them.
Quick answers
Short answers to the searches that lead to this page. Grid sizes and the 4 mm starting point come from the references named above.
- Where are chip carving patterns free as a printable PDF? Santa Clara Valley Carvers, READ N TRY and Lora Irish publish free printable patterns. My Chip Carving offers practice patterns through a signup form.
- What are easy chip carving patterns for beginners? Rows of three-cut triangles on a 4 mm grid, then a zigzag border and diamonds. Leave rosettes until straight chips pop out whole.
- How do you draw chip carving patterns? Rule a square grid with a hard pencil, a ruler and a small T-square, then join grid points into triangles. A compass draws the rosette.
- What grid size should a beginner use? 4 mm. A chip from a 5 mm grid has twice the volume and is much harder to remove.
Use this chart
Print it, save the image version, or put it on your own site or forum post with the code below. The code keeps a link back to this page as the source.
Embed code
<a href="https://carvingbench.com/blog/chip-carving-practice-patterns"><img src="https://carvingbench.com/charts/chip-carving-practice-patterns/image.png" alt="Chip Carving Practice Patterns: Six Beginner Sheets and Free Pattern Sources" width="600" loading="lazy"></a> <p>Source: <a href="https://carvingbench.com/blog/chip-carving-practice-patterns">Chip Carving Practice Patterns: Six Beginner Sheets and Free Pattern Sources</a>, Carving Bench</p>
What you need for this
- See price on AmazonAmazon
Flexcut KN15 chip carving knife, 1 in blade
From Best Chip Carving Knives: Cutting Knife, Stab Knife and Starter Sets
- See price on AmazonAmazon
BeaverCraft BW19 Basswood Carving Blocks
From Best Basswood Carving Blocks: Sizes, Pack Counts and Price per Block
- See price on AmazonAmazon
Bacher leather strop 12.6 in, 4 compounds and balm